Easier way to apply tissue?

Ask other modelers for a little help / knowledge ?

Easier way to apply tissue?

Postby Tabitha64 » Thu May 23, 2013 9:13 pm

I am looking for any and all tips on applying the tissue. I have seen were someone recommend stick glue to apply tissue to area then using Dope to tighten. Picture would help visual. Thanks again. Tabitha :)
Tabitha64
 
Posts: 33
Joined: Sun May 20, 2012 9:59 am

Re: Easier way to apply tissue?

Postby Wildpig » Thu May 23, 2013 9:47 pm

time lapse video, covering a balsa airplane with tissue using a glue stick:
http://www.youtube.com/watch?v=qs-RsfnqBKc
Wildpig
 
Posts: 529
Joined: Thu Jan 26, 2012 9:41 am

Re: Easier way to apply tissue?

Postby limey » Fri May 24, 2013 8:07 am

Try tissue paste I think used more in the UK but seems scarce in the us not sure if it is available there but if I it is its worth a try. Good luck. Limey
limey
 
Posts: 36
Joined: Mon Aug 06, 2012 7:51 am

Re: Easier way to apply tissue?

Postby Mitch » Fri May 24, 2013 10:27 am

You can also use Elmers "white glue" or similar. It is water based, thin it down with water and apply with brush to the contact area. Then attach the paper.
After that is dry, wet the paper with water. That will shrink the paper. Then apply the "dope" to seal the paper. Mitch
Mitch
 
Posts: 1347
Joined: Mon Aug 22, 2011 9:16 pm
Location: Kent, WA

Re: Easier way to apply tissue?

Postby Tabitha64 » Fri May 24, 2013 4:29 pm

Thank you that does help a lot. I need help for edges like wing tips. Video really helped. Thanks again.
Tabitha64
 
Posts: 33
Joined: Sun May 20, 2012 9:59 am

Re: Easier way to apply tissue?

Postby davidchoate » Mon Sep 02, 2013 1:04 pm

i use a GOOD glue stick. like Elmers. Make sure u run the grain correctly. ionce its on the frame I use a wet paper towel to shrink it. i heard that a 50/50 mix of Elmers glue and water woks well in place of dope, but I havent tried it yet.
davidchoate
 
Posts: 1263
Joined: Wed Aug 14, 2013 6:41 am
Location: PHiladelphia PA

Re: Easier way to apply tissue?

Postby stx44 » Mon Sep 02, 2013 5:26 pm

After reading the comments about glue sticks I googled it and found a couple of usefull videos, and now its just trial and error (I am getting better....ummmm, I think..)

Sorry dont know how to post links...
stx44
 
Posts: 92
Joined: Wed Aug 28, 2013 9:15 am

Re: Easier way to apply tissue?

Postby David Lewis » Mon Sep 02, 2013 7:53 pm

The trick to water shrinking tissue is to use as little water as possible. Spray a fine cloud into the air and waft the part through the mist. Just enough moisture so that the tissue starts to sag.

If you dope the tissue, airbrush on a very light, thinned dry coat. Let that cure until dry to the touch, sand it with fine sandpaper to remove the fuzz and then gradually build it up with more thin coats.
David Lewis
 
Posts: 289
Joined: Thu Jun 13, 2013 11:47 am
Location: Orlando FL

Re: Easier way to apply tissue?

Postby Steve Blanchard » Tue Sep 03, 2013 11:25 am

In regard to water shrinking tissue it is all situational. I usually soak my tissue with alcohol not water. It shrinks tight. If I was using water I would do the same. I DO NOT Shrink the tail feathers on my airplanes unless there is an airfoil.

Steve
Steve Blanchard
 
Posts: 343
Joined: Tue Jun 14, 2011 10:08 am


Return to General Building Questions

Who is online

Users browsing this forum: No registered users and 51 guests