Thomas Morse Scout
8 posts
• Page 1 of 1
Thomas Morse Scout
by dbcisco » Fri Aug 21, 2009 11:46 pm
Just opened this and started putting it together. I looooove the laser cut parts. This is the first laser cut kit I ever had. Using super glue and it is going well except I forgot my mask and now I have a migraine. Many people are very sensitive to CA and I am one of them. Will post picks soon.
A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
by dbcisco » Sat Aug 22, 2009 4:19 am
Once again, I can't seem to make heads nor tails of the plans for the fuselage. It seems I'll have to wing it again. It doesn't matter as I have to mod it to take electric power anyway. Lightening the tail, making room in the nose,strengthening the cabane strut reinforcements and redesigning the landing gear supports. At least the wing drawings seem readable.
A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
by dbcisco » Tue Aug 25, 2009 1:41 pm
flash52 wrote:Nice looking plane. Are you going to have the rotary spin with the prop?
I was going to but the cowl will cover it up so I decided the airflow is more important.
A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
by dbcisco » Wed Sep 02, 2009 9:09 pm
I beefed up the tail feather with a single wide piece of balsa instead of thin stringers. Elevators connected by CF rod. Floppy disk hinges installed. These should withstand the monocote (opaque OD) and it wont need much shrinking.
A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
by dbcisco » Sun Sep 27, 2009 11:46 am
It's coming along nicely now. Coverlite worked better than Monocote, I got the wings built and covered (no foam on this one ). Here are pics of the tail feathers with floppy-disk hinges and one pic of the entire plane so far. Landing gear is next.
[/img]
[/img]A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
by dbcisco » Sat Oct 03, 2009 10:29 pm
All done. 9 Oz. with battery!!! CG is at leading edge of bottom wing, a little nose heavy (for a change).
A bumblebee isn't supposed to fly but does.
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
My plane is supposed to fly but doesn't.
Balances out doesn't it : )
- dbcisco
- Posts: 209
- Joined: Fri May 30, 2008 8:34 am
- Location: Lansdale, PA
8 posts
• Page 1 of 1
Return to General Building Questions
Who is online
Users browsing this forum: No registered users and 30 guests